|
grumpyoleman -> Homemade Chasity Cage (11/20/2014 9:11:03 PM)
|
I’ve always been into BDSM, but only the past few years have I experimented with chastity. My cage was “one of the plastic models”, regardless of what ring or spacer size used it was uncomfortable, plus “pullout was very easy”. The “final straw” was when the tube split and pinched/cut my penis. As a DIY, I decided to build a cage and wanted the following: comfort, escape proof, anti-pull out without being pierced (the biggest challenge), unable to masturbate, and a device I could construct. After 3 attempts and resizing I accomplished the above.
I read about comments on various cages for ideals, advantages and disadvantages. Most agreed MM was a good product; therefore I leaned toward constructing a “jailbird style” using my modifications. I used 1/8, 1/4 and 3/8” stainless tubing. I only have simple hand tools and not a machine shop. I don’t have a welder; therefore I used a plumber’s torch with Mapp gas to braze everything together. The base ring is made of 3/8”, (larger diameter tubing for comfort around the scrotum) the cage is ¼ and 1/8” stainless tubing. This is my anti-pullout and anti-masturbate solution. Anti-masturbate==I brazed small “tips” inside of cage, if I try to masturbate or move the cage rapidly these quickly become painful causing “Major Discomfort” to penis. The first “tips” were too large, too sharp and rubbed raw places after a day. (Try to imagine tiny BB’s or very coarse sandpaper inside your cage continuously rubbing again your penis) I used a dremel to smooth them out some. I also installed an extra bar under the cage for closer spacing to prevent using finger or other object from rubbing or playing with the “sensitive” area under the penis.
Anti-pullout (The toughest challenge)== from the rear of the cage backwards I brazed on 5,,¼ “horseshoe shaped pieces bend from the ¼” tubing. That covers the top rear area of the penis and extends approx. one and ¼“ backwards into the groin area covering the top rear portion of the penis. Being their horseshoe shaped and open on the bottom that allows the penis to be inserted as any cage, but it only covers the top rear area of the penis. (Visualize it as a covering on top of the penis behind the rear cage ring which extends backwards into your body) I CANNOT push the cage forward enough to uncover the top of my penis due to the top rear cover, therefore I can’t get to my cock to pull it out!!
Remember I brazed everything? I also intentionally left the brazing semi-rough here for anti-masturbating purposes. Plus if I push the cage forward trying to get enough room to pullout, the outer rear brazing “digs” into my groin not allowing much forward movement and again any masturbating movements or rapid fast movements cause’s abrasion and “Major Discomfort” I used a security screw and plastic numbered seal instead of a padlock. (That’s everyone’s personal preference and has been debated in other forums) My brazing is NOT pretty, therefore I’m NOT posting any photos of final product, however I may do a sketched drawing later. Basically my cage is a MM jailbird with “tips” inside and a cover extended backwards covering top rear area of penis. BTW the rear covering is not uncomfortable extending backwards in to the body. The only issue I’ve had is cold days and “TheBoys” drawing up causing the base ring to pinch and burn some, applying lotion resolves the situation. (Maybe if I make a little larger base ring, this would not happen)
I don’t have a KH or Domme, however, I’ve been able to make myself stay locked for 2 weeks. Though I could pullout anytime with the “Plastic Model” I never “cheated” or “relieved” myself if locked up, but I didn’t realize how mentally challenging it is if you CANNOT escape or pullout. Hopefully someday I will hear the words of a Wonderful lady saying, “Your cock is locked and mine, if the seal gets broke, I will have NO mercy on your behind !!!!!!
I know there will be some critics, however this works great for me and I CANNOT masturbate, pullout or escape……
|
|
|
|
